Multi Current Universal Smart Charger For Any 2 4 7 2 V Nimh Nicd Battery Pack

Features

• Universal Smart Charger is designed for any NiMH/NiCd battery pack from 2.4V- 7.2V with capacity > 600mAh
• 100-240V AC input for world wide power support.
• Ideal for 4.8V - 7.2V NiMH battery packs of RC flight, RC car, Bikelighting and rechargeable flashlight.
• It can alse be use as a battery charger module for any DC device
• It is a very smart charger. Just plug it in and wait for battery to charge
  • Automatically detect battery pack's voltage, Red LED will be on during charging.
  • Automatically cut-off by negative delta V when battery pack is fully charge.
• When battery is fully charge, LED will change from Red to Orange color.
• Two current levels 0.6A and 1.2A, are selectable by a switch
  • For battery pack less than or equal to 1200mAh, please switch charging rate to 0.6A
  • For battery pack over 1200 mah, please switch charging rate to 1.2 A
• The fuse is installed in power line for protection of over current, short circuit & reverse polarity protection. It is easy to replace. Two extra fuse is included .
• Charging time is about 4 hrs for 4500 mAh battery pack, 1.5 hrs for 1800 mAh, and 1hr for 1200 mAh.
• One standard Tamiya male connector is installed with the charger.
• One set of Clip adapter with a female tamiya connector included for charging any battery packs.
• One connector adaptor from standard Female Tamiya to Male Mini. Tamiya for charging RC air battery packs.

Cautions:

• The charger is designed for fast charging NiCD and NiMH battery packs from 2.4V to 7.2V battery. with capacity > 600 mAh.
  • Please don't use the charger for low capacity battery pack (600mah).
  • Please don't charge battery pack with voltage < 2.4V or voltage > 7.2V
  Strongly suggest to use Tenergy brand high drain rate battery pack. We are not responsible for any damage cause by charging other brand battery using this charger. Please make sure polarities between charger and battery pack are match before charging the battery. Otherwise wrong polarity may burn the fuse and damage the charger. The charger is designed for indoor use only. The charger should be horizontally position and work in well ventilated condition. Avoid it being wet and keep it away from flammable/ explosive goods. Cut off the power supply before connecting or disconnecting the charger with batteries.
• Don't try to disassemble the charger because of the high voltage inside, danger!!!

• Universal Fast and Smart Charger is designed for charging any 24V NiMH and NiCd Battery Packs. (20 Cells pack)
• 120-240V AC input for worldwide use.
• The charger can cut-off power Automatically by negative delta V IC when battery pack is fully charge.
• Two current levels, 0.6A and 1.2A, are selectable by a switch for either higher or lower capacity battery pack.
  • For battery pack between 3300mah and 500 mah, please use the low level switch -- charging rate: 0.6A
  • For battery pack over 3300 mAh, please use the high level switch -- charging rate: 1.2A
• Approximate, Charging time( hours) = Battery capacity ( Ah) / charging current ( A).
• If possible, always choose charging current in 0.6A to slow charging , which is good for battery and charger service life.
• Protection fuse for over current, short circuit & reverse polarity protection.
• Charging time can be estimated as the follow:

Charging time ( Hrs ) = 1.2xBattery capacity ( mAh) / Charging current ( 0.6A or 1.2A )

• One standard Tamiya male connector installed with the charger.
• One set connector adaptor from female tamiya to Clips is included for charging any battery packs.
• It is a very smart charger. Just plug it in and wait for the battery to get charge.
• The charger is designed for fast charging any 24V Nicd and NiMH battery packs. Ideal for 24V battery pack for E-bike, E- scooter and hunting light
• Dimension: 1.5"H X 2.5"W X 5.5"L.
• Weight: 0.6LB.

Features and Benefits

• Best Charger for charging all RC Car, RC air and Airsoft battery packs 7.2V, 8.4V, 9.6V and 12V.
  
• Universal for for any NiMH /NiCd battery packs 7.2V - 12V (6-10 Cells pack)
  
• Fast charger with current switch to select either, 0.9A and 1.8A. Deliver full charge within 1 - 2 hours.
  
• Charging Current 0.9A for battery packs with capacity from 1100mAh -2200mAh. For 2000mAhpack, charging time is 1 hour.
  
• Charging Current 1.8A for battery packs with capacity above 2000mAh. For 3000mAh pack, charging time is 1.5 hours.
  
• Smart Charger:with automatic voltage detection.
  
• Use pulse and negative pulse technology to avoid battery overheating during fast charging, optimized for battery pack's cycle life.
  
• Red LED will be on during charging.
  
• Automatically charging ending with negative delta V.
  
• Worldwide usage with 120-240V AC
  
• Safety protection fuse for over current, short circuit & reverse polarity protection.

Accessories Included

• 1 standard Tamiya Female connector and Fuse house with the smart battery charger.
  
• 1 connector adaptor from standard Male Tamiya to Mini Female.
  
• 1 set of clip adaptor with Male Tamiya connector on one end.
  
• 4 additional fuses
  

Smart Charger Specification

• FOR 6V-12V NI-MH/NI-CD BATTERY PACK 6-10PCS BATTERY
  
• Input: AC100-240V
  
• Output: 6-12V 0.9or1.8A

Operation Instruction

• Connect battery pack to output connector and plug AC power source.
  
• Make sure battery polarity is connected correctly (Red wire is positive)
  
• Charger will detect battery voltage automatically, Red LED will be on during charging
  
• When battery is fully charged, current will reduce to trickle charging at 50mA,Green LED will be on
  
• Battery will be charged at 0.9A or 1.8A constant current,
  
• Approximate Charging time is about 1.5hrs for 3000mAh battery,1hr for 1800mAh battery.
  
• The charger is designed for faster charging NiCd and NiMH battery packs from 6 to 12V for RC car/Air and Air soft gun.
  
• Don't charger battery pack with voltage less than 6V or Voltage bigger than 12V and Capacity smaller than1100mAh.
  
• Battery pack must be made by high drain current cell.
  
• Please contact your seller for instruction. Mfg is not responsible for any damage and consequent damage by Misusage.
  
  

Caution

• The charger is designed for indoor use only.
  
• The Charger should be horizontally positioned and work in well ventilated condition, avoid wet and keep it away from inflammable explosive goods.
  
• Don't cover the charger when charging, ambient temperature shall not be more than 40^oC
  
• Don't touch the plug.
  
• Cut off the power supply before connect or disconnect the charger with batteries.
  
• Don't try to disassemble the charger, High voltage inside, danger!

Features and Benefits

• Best Charger for charging all NiMH/NiVD battery packs 12V,13.2V,14.4V,15.6V,16.8V
  
• Universal for for any NiMH /NiCd battery packs 12V - 16.8V (10-14 NiMH/NiCD Cells packs)
  
• Fast charger with current switch to select either, 0.7A and 1.4A. Deliver full charge within 1 - 2 hours.
  
• Charging Current 0.7A for battery packs with capacity from 1100mAh -2200mAh. For 2000mAhpack, charging time is 1 hour.
  
• Charging Current 1.8A for battery packs with capacity above 2000mAh. For 3000mAh pack, charging time is 1.5 hours.
  
• Smart Charger:with automatic voltage detection.
  
• Use pulse and negative pulse technology to avoid battery overheating during fast charging, optimized for battery pack's cycle life.
  
• Red LED will be on during charging.
  
• Automatically charging ending with negative delta V.
  
• Worldwide usage with 120-240V AC
  
• Safety protection fuse for over current, short circuit & reverse polarity protection.

Accessories Included

• 1 standard Tamiya Female connector and Fuse house with the smart battery charger.
  
• 1 connector adaptor from standard Male Tamiya to Mini Female.
  
• 1 set of clip adaptor with Male Tamiya connector on one end.
  
• 3 additional fuses
  
  

Smart Charger Specification

• FOR 12V-16.8V NI-MH/NI-CD Battery Packs (10-14 Cells in series )
  
• Input: AC100-240V
  
• Output: 12V-16.8V 0.7or 1.4A

Operation Instruction

• Connect battery pack to output connector and plug AC power source.
  
• Make sure battery polarity is connected correctly (Red wire is positive)
  
• Charger will detect battery voltage automatically, Red LED will be on during charging
  
• When battery is fully charged, current will reduce to trickle charging at 50mA,Green LED will be on
  
• Battery will be charged at 0.7A or 1.4A constant current,
  
• Approx, Charging time is about 2 hrs for 3000mAh battery,1.5hr for 1800mAh battery.
  
• Don't charger battery pack with voltage less than 12V or Voltage bigger than 12V and Capacity less than 1100mAh.
  
• Please contact your seller for instruction. Mfg is not responsible for any damage and consequent damage by Misusage.
  
  

Caution

• The charger is designed for indoor use only.
  
• The Charger should be horizontally positioned and work in well ventilated condition, avoid wet and keep it away from inflammable explosive goods.
  
• Don't cover the charger when charging, ambient temperature shall not be more than 40^oC
  
• Don't touch the plug.
  
• Cut off the power supply before connect or disconnect the charger with batteries.
  
• Don't try to disassemble the charger, High voltage inside, danger!